INDUSTRY NEWS
CURRENT LOCATION :HOME > NEWS CENTER > INDUSTRY NEWS
Six tips for maintenance and repair of fully enclosed plastic towline bridge plastic towline
Click rate: Release time:2020-05-05 Information sources:本站

Six tips for maintaining bridge plastic towline
(1) Scrub the appearance of equipment

1.The appearance is free of yellow robe, no greasy dirt, and the natural appearance is seen. The appearance parts are complete and no damage.

2.There is no black oil and rust on the guide rails, racks, smooth bars, and lead screws, and the grinding burrs are removed.

(2) Clean and unblock the lubricating and cooling system, pipelines, including oil holes, oil cups, oil lines, and linoleum filter installation.

1. The oil window is clear and bright, the oil mark is eye-catching, the oil is in place, and the oil quality meets the requirements.

2.The oil tank, oil sump, and filter installation are cleaned inside and outside without dirt and impurities.

3.The oil line is complete, the linoleum is not aging, and the maintenance of the bridge type plastic towline is smooth, and there is no oil leakage or water leakage.

4.The oil gun and oil pot are clean and easy to use, the oil nozzle and oil cup are complete, and the hand pump and oil pump are easy to use.

5.Remove the protective covers of each part, check the lubrication situation, and scrub the guide rails, smooth bars, and screws.

(3) Check and adjust the iron filings, pressure plates, and gaps of each part, and the fixing screws, nuts, and handles of each part are flexible and easy to use.

1. The gap between the oblique iron, pressure plate and sliding surface of each part is adjusted to within 0.04mm, and the moving parts can move freely.

2. There is no looseness of the fixing screws and nuts in each part.

(4) Check each safety installation

1. All limit switches, indicator lights, signals, safety protection installation, complete and reliable.

2. Maintain the insulation of all electrical appliances of the bridge plastic towline, install the reliable grounding, and illuminate safely.

(5) Check that each department of electrical appliances meets the requirements

1. The inside and outside of the electric box are clean, free of dust and debris, and the door of the box is not damaged.

2.The original electrical appliances are fastened and easy to use, the lines are neat and the line numbers are clear and complete.

3. The motor is clean and free of grease, dust, fans, and covers.

4.The snake skin tube has no shedding, breakage, grease, and waterproof elbows.

(6) Cleaning around the work site

1. There is no iron debris around the equipment.

2. Maintain bridge plastic towline machine tool accessories, tools, and fixtures in a reasonable arrangement, clean and fixed. To achieve the above points, I believe that it can definitely extend the service life of your bridge plastic energy chain.


2


Maintenance and repair of fully enclosed plastic towline
Fully enclosed plastic towline is the same as all mechanical equipment. If you want to maintain a good working condition and increase the service life, you need frequent maintenance and repair, timely discover and eliminate hidden dangers, prevent accidents before they occur, so as to ensure safe operation and reduce losses .

For the newly purchased cable towline, since each unit chain is unused, the friction is large. To reduce friction, you can add some lubricating oil to reduce friction and increase its flexibility. Be careful not to add too much and prevent Lubricating oil splashes on the opening of the cover plate to prevent it from falling off during operation and causing unnecessary losses.

In the process of using fully enclosed plastic towline, make sure to listen, watch and change. The so-called one is to listen to the sound of the fully enclosed plastic towline in operation. During normal operation, the sound is single and light, and it runs almost silently. After a long period of use, when there is a problem, such as cracks, the sound There will be a harsh sound; the second look is to do regular inspections, the first is the connector, mainly to see whether there is a problem with the installation hole. The second is the shaft, depending on the wear. Once again, the cover plate and the mounting holes, see if there are cracks, whether the mounting holes have slipped, etc .; the third replacement is to find the problematic unit chain and replace it with a new one to prevent the problem from becoming larger and causing greater losses. Of course, when major problems occur, you need to replace them all.

Completely closed plastic towline can be repaired without maintenance. If it is not repaired, it needs to be replaced. So as soon as the problem is discovered, the problem can be solved as soon as possible, which can save money, eliminate small hidden dangers, and ensure great safety. Maintenance and repair of fully enclosed plastic towline
Fully enclosed plastic towline is the same as all mechanical equipment. If you want to maintain a good working condition and increase the service life, you need frequent maintenance and repair, timely discover and eliminate hidden dangers, prevent accidents before they occur, so as to ensure safe operation and reduce losses .

For the newly purchased cable towline, since each unit chain is unused, the friction is large. To reduce friction, you can add some lubricating oil to reduce friction and increase its flexibility. Be careful not to add too much and prevent Lubricating oil splashes on the opening of the cover plate to prevent it from falling off during operation and causing unnecessary losses.

In the process of using fully enclosed plastic towline, make sure to listen, watch and change. The so-called one is to listen to the sound of the fully enclosed plastic towline in operation. During normal operation, the sound is single and light, and it runs almost silently. After a long period of use, when there is a problem, such as cracks, the sound There will be a harsh sound; the second look is to do regular inspections, the first is the connector, mainly to see whether there is a problem with the installation hole. The second is the shaft, depending on the wear. Once again, the cover plate and the mounting holes, see if there are cracks, whether the mounting holes have slipped, etc .; the third replacement is to find the problematic unit chain and replace it with a new one to prevent the problem from becoming larger and causing greater losses. Of course, when major problems occur, you need to replace them all.